S&K Gunsmithing's prices are very competitive - our per hour service charge is $35, with a minimum charge of $20.
Appraisals available upon request!
Sight Work | Price |
---|---|
Range sight-in | $25 (Ammunition Extra) |
Bore sighting | $20 |
Drill and tap barrel (per hole) |
$20 |
Install front ramp (Sweat-on) |
$40 - $70 |
Install front ramp (Screw-on) |
$30 - $60 |
Install front or mid bead |
$20 - $40 |
Receiver sights | $20 - $40 |
Scope mounting (drilled & tapped) | $25 - $45 |
General Barrel, Action, and Rifle Work | Price |
---|---|
Check head space | $20 - $40 |
Stuck case removal | hourly |
Remove live round | $40 - $125 |
Remove obstruction from bore |
hourly |
Cut and crown barrel |
$30 - $80 |
Cut and weld bolt handle |
$40 - $90 |
Make and install spring |
$25 - $75 |
Safety installation | hourly |
Trigger adjustment or install | $45 - $200 |
Replace or repair parts | hourly |
Shotgun | Price |
---|---|
12 ga long forcing cone | $40 to 70 per barrel |
Dent raising 12 ga only | $50 - $100 |
Polish chamber or bore | $30 - $70 per barrel |
Open fixed chokes |
$35 to $75 per barrel |
Refitting hinge pin |
$75 - $200 |
Measure inside dia. of bore or choke |
$10 - $20 |
Install & Furnish Plug |
$20 - $30 |
Handgun | Price |
---|---|
Revolver action job | $50 to $120 |
Semi-auto action job | $50 - $140 |
Fit barrel to 1911 | $40 - $100 |
Fit barrel bushing to 1911 |
$20 to $40 |
Open or modify ejection port on 1911 |
$20 - $60 |
Polish throat and ramp on 1911 |
$25 - $50 |
Fit new trigger to 1911 | $20 - $40 |
Fit custom hammer to 1911 | $40 - $100 |
Cure push off on revolver |
$35 to $60 |
Retime revolver |
$20 - $60 |
Fit new extractor 1911 |
$40 - $70 |
Stock Work | Price |
---|---|
Re-stock | by quote |
Complete refinishing | $80 - $150 |
Re cut checkering | $50 - $100 |
Glass bedding action |
$50 to $100 |
Float barrel |
$35 - $60 |
Install pad labor only |
$30 - $60 |
Install swivels | $20 - $50 |
Install cross bolt supports | $40 - $70 |
Install recoil reducer, simple |
$25 to $50 |
Install recoil reducer, drill |
$50 - $80 |
Inletting of stock |
$150 - $300 |
Install synthetic stock |
$50 - $100 |
Crack repair | hourly |
Lengthen/shorten stock | $25 - $70 |
Metal Finishing | Price |
---|---|
Basic bead blast, polish to 220 to 320 grit finish, hot salt blue | $90 - $130 |
Master finish remove most or all blemishes, polish to 400 grit finish, hot salt blue | $140 - $220 |
Baking lacquer or teflon finish |
$90 - $180 |
Draw Filing |
hourly |
Note: All metal refinishing includes complete cleaning and inspection of parts also! |
Included |
Gun Cleaning | Price |
---|---|
Partial cleaning | $20 - $30 |
Complete cleaning | $40 - $90 |